工作原理:電除塵器是一種采用靜電除塵方法收集煙氣中的粉塵的裝置.是一種理想的工業廢氣凈化設備.它的純化取決于電極和沉淀系統.當輸入高壓直流電(dc)在兩極之間的電極空間時,產生負離子、陽離子,并通過排氣微粒表面靜電場,在電場力作用下移動其極性相反的電極,并沉積在電極上,達到除塵的目的.

    雙極系統都有一個振動裝置,當振動錘周期性地敲擊雙極裝置時,附著在其上的灰塵被吹去,落入下灰斗,由排灰裝置排出機器.凈化后的廢氣通過煙囪排入大氣,完成煙氣凈化過程.

    安裝要求:電除塵器安裝前,了解電除塵器的總圖、安裝圖和說明書,并嚴格遵循圖紙.制造商的裝配:框架應在工廠裝配,兩條對角線之間的差異不應大于對角線長度的1/1000,平面度應為10mm.

    放電電極懸浮架每節也用螺栓裝配,兩對角水之間的對角線長度相差1/1000以上,在懸掛狀態下框架高度小于或等于5米時,其平整度為5毫米,當框架高度超過5米時其平整度達到10毫米.裝配后的車架應標記為現場安裝.配電驅動裝置、沉淀電極、電極傳動裝置、旋轉卸料機和支架應裝配并送到現場.

    現場安裝:在安裝設備前,檢查土建基礎的尺寸.如有差異,支座應安裝在基面上并與水平儀找平.根據設備清單進行盤點檢查.在安裝引起吊裝和長期堆放變形的部件之前,采取糾正措施.如果制造偏差超過設計要求,應對主要部件進行抽樣檢驗.如果沒有,應該報廢.

    電極和沉淀系統的所有部分都應應用于油漆制造商,如果工廠沒有涂層,則應予以應用.這種的油漆是導電涂料,如果你不能購買煤油和炭黑敷料代替.傳動件清洗、加油等參考(機械設備安裝施工及驗收規范)實施.